RegistersEdit
| Old3DS | Name | Address | Width | Used by |
|---|---|---|---|---|
| Yes | CFG9_SYSPROT9 | 0x10000000 | 1 | Boot9 |
| Yes | CFG9_SYSPROT11 | 0x10000001 | 1 | Boot9 |
| Yes | CFG9_RST11 | 0x10000002 | 1 | Boot9 |
| Yes | CFG9_DEBUGCTL | 0x10000004 | 4 | |
| Yes | CFG9_XDMA_CNT | 0x10000008 | 1 | Boot9, Process9, TwlProcess9 |
| Yes | CFG9_CARDCTL | 0x1000000C | 2 | Process9 |
| Yes | CFG9_CARDSTATUS | 0x10000010 | 1 | Process9 |
| Yes | CFG9_CARDCYCLES0 | 0x10000012 | 2 | Boot9, Process9 |
| Yes | CFG9_CARDCYCLES1 | 0x10000014 | 2 | Boot9, Process9 |
| Yes | CFG9_SDMMCCTL | 0x10000020 | 2 | Process9 |
| Yes | ? | 0x10000100 | 2 | |
| No | CFG9_EXTMEMCNT9 | 0x10000200 | 1 | NewKernel9 |
| Yes | CFG9_MPCORECFG | 0x10000FFC | 4 | |
| Yes | CFG9_BOOTENV | 0x10010000 | 4 | |
| Yes | CFG9_UNITINFO | 0x10010010 | 1 | Process9 |
| Yes | CFG9_TWLUNITINFO | 0x10010014 | 1 | Process9 |
CFG9_SYSPROT9Edit
CFG9_SYSPROT9 is used to permanently disable certain security-sensitive ARM9 memory areas until the next hard reset.
| Bit | Description | Used by |
|---|---|---|
| 0 | Disables ARM9 bootrom(+0x8000) when set to 1, and enables access to FCRAM. Cannot be cleared to 0 once set to 1. | Boot9 |
| 1 | Disables OTP area when set to 1. Cannot be cleared to 0 once set to 1. | NewKernel9Loader, Process9 |
| 31-2 | Not used |
On Old 3DS, NATIVE_FIRM reads CFG9_SYSPROT9 to know whether it has previously initialized the TWL console-unique keys using the OTP data. After setting the TWL console-unique keys, NATIVE_FIRM sets CFG9_SYSPROT9 bit 1 to disable the OTP area. In subsequent FIRM launches prior to the next reset, NATIVE_FIRM will see that the OTP area is disabled, and skip this step.
On New 3DS, the above is instead done by the Kernel9 loader. In addition to using the OTP data for initializing the TWL console-unique keys, the Kernel9 loader will generate the decryption key for NATIVE_FIRM. The final keyslot for NATIVE_FIRM is preserved, so that at a non-reset FIRM launch, the keyslot can be reused, since the OTP would then be inaccessible.
CFG9_SYSPROT11Edit
| Bit | Description | Used by |
|---|---|---|
| 0 | Disables ARM11 bootrom(+0x8000) when set to 1, and enables access to FCRAM. Cannot be cleared to 0 once set to 1. | Boot9 |
| 31-1 | Not used |
CFG9_RST11Edit
| Bit | Description | Used by |
|---|---|---|
| 0 | Presumably takes ARM11 out of reset. Cannot be set to 1 once it has been cleared. | Boot9 |
| 31-1 | Not used |
CFG9_XDMA_CNTEdit
Write 1 to enable XDMA for the device, 0 to disable. Always enabled for CTRCARD (ids 0 and 1), NTRCARD (id 8), and SHA (id 6 for infifo and 7 for outfifo).
| Bit | Description | Used by |
|---|---|---|
| 0 | SDIO controller 1 (eMMC and usually SD card; XDMA device ID: 2) | |
| 1 | SDIO controller 3 (SD card if configured so; ID: 3) | |
| 2 | AES Input FIFO (ID: 4) | Boot9, Process9, TwlProcess9 |
| 3 | AES Output FIFO (ID: 5) | Boot9, Process9, TwlProcess9 |
| 31-4 | Reserved |
CFG9_CARDCTLEdit
| Bit | Description | Used by |
|---|---|---|
| 1-0 | Gamecard active controller select (0=NTRCARD, 1=?, 2=CTRCARD0, 3=CTRCARD1) | Process9 |
| 8 | 1 = Switch to SPICARD interface (savegames). | Process9 |
Depending on the gamecard controller that has been selected, one of the following gamecard registers will become active:
- Selecting NTRCARD will activate the register space at 0x10164000.
- Selecting CTRCARD0 will activate the register space at 0x10004000.
- Selecting CTRCARD1 will activate the register space at 0x10005000.
CFG9_CARDSTATUSEdit
| Bit | Description | Used by |
|---|---|---|
| 0 | Cartridge-slot empty (0=inserted, 1=empty) | Process9 |
| 3-2 | Cartridge-slot power supply (0=off, 1=prepare power regulator, 2=enable output, 3=request power down) | Process9 |
When the power supply is in the "request power down" state, the power bits will be reset to 0=off after some time.
CFG9_SDMMCCTLEdit
This register controls power of multiple ports/controllers and allows to map controller 3 to ARM9 or ARM11. The SD card can be accessed on ARM11 by setting bit 8 and clearing bit 9.
| Bit | Description | Used by |
|---|---|---|
| 0 | Controller 1/3 port 0 power (SD card) (1=off) | Process9 |
| 1 | Controller 1 port 1 power (eMMC) (1=off) | Process9 |
| 2 | Controller 2 port 0 power (WiFi SDIO) (1=off) | Process9 |
| 3 | Controller 3 port 1 power? Set at cold boot. | - |
| 4-5 | Unused. | - |
| 6 | Wifi port related? Pull up? Set at cold boot. | - |
| 8 | Controller 3 mapping (0=ARM9 0x10007000, 1=ARM11 0x10100000) | Process9 |
| 9 | SD card controller select (0=0x10007000/0x10100000, 1=0x10006000) | Process9 |
| 10-15 | Unused. | - |
CFG9_EXTMEMCNT9Edit
This register is New3DS-only.
| Bit | Description | Used by |
|---|---|---|
| 0 | Hide extended ARM9 memory (0=hidden, 1=shown) | Kernel9 (New3DS) |
| 31-1 | Reserved |
CFG9_MPCORECFGEdit
Identical to PDN_MPCORE_CFG.
CFG9_BOOTENVEdit
This register is used to determine what the previous running FIRM was. Its value is kept following an MCU reboot. Its initial value (on a cold boot) is 0. NATIVE_FIRM sets it to 1 on shutdown/FIRM launch. LGY FIRM writes value 3 here when launching a TWL title, and writes value 7 when launching an AGB title.
NATIVE_FIRM will only launch titles if this is not value 0, and will only save the AGB_FIRM savegame to SD if this is value 7.
CFG9_UNITINFOEdit
This 8-bit register is value zero for retail, non-zero for dev/debug units.
CFG9_TWLUNITINFOEdit
In the console-unique TWL key-init/etc function the ARM9 copies the u8 value from REG_UNITINFO to this register.
This is also used by TWL_FIRM Process9.