Difference between revisions of "CONFIG9 Registers"
| Line 37: | Line 37: | ||
| 2 | | 2 | ||
|- | |- | ||
| − | | | + | | REG_BOOTENV |
| 0x10010000 | | 0x10010000 | ||
| 4 | | 4 | ||
| Line 78: | Line 78: | ||
== REG_UNITINFO == | == REG_UNITINFO == | ||
This 8-bit register is value zero for retail, non-zero for dev/debug units. | This 8-bit register is value zero for retail, non-zero for dev/debug units. | ||
| + | |||
| + | |||
| + | == REG_BOOTENV == | ||
| + | 0=Cold boot, 1=CTR, 3=TWL, 5=NTR, 7=AGB | ||
| + | |||
| + | It is unknown if this register controls anything. | ||
Revision as of 02:56, 9 November 2014
Registers
| NAME | PHYSICAL ADDRESS | WIDTH |
|---|---|---|
| REG_SYSPROT9 | 0x10000000 | 1 |
| REG_SYSPROT11 | 0x10000001 | 1 |
| ? | 0x10000004 | 4 |
| REG_CARDCONF | 0x1000000C | 2 |
| REG_CARDCTRL | 0x10000010 | 1 |
| ? | 0x10000011 | 1 |
| ? | 0x10000012 | 2 |
| ? | 0x10000204 | 2 |
| REG_BOOTENV | 0x10010000 | 4 |
| REG_UNITINFO | 0x10010010 | 1 |
REG_CARDCONF
| Bit | Description |
|---|---|
| 1-0 | Gamecard active controller select (0=NTRCARD, 1=?, 2=CTRCARD1, 3=CTRCARD2) |
| 8 | ? |
Depending on the gamecard controller that has been selected, one of the following gamecard registers will become active:
- Selecting NTRCARD will activate the register space at 0x10164000.
- Selecting CTRCARD1 will activate the register space at 0x10004000.
- Selecting CTRCARD2 will activate the register space at 0x10005000.
REG_SYSPROT9
Writing values to SYSPROT sets the specified bitmask. The ARM9 bootrom(+0x8000) is disabled by writing bit0. bit1 is used by NATIVE_FIRM to make sure console-unique TWL AES-keys are only set at hard-boot. It is not possible to set any other bits.
From disassembly of the New3DS process9, it appears that setting bit1 disables the 0x10012000+ region.
REG_SYSPROT11
ARM11 bootrom (+0x8000) is disabled by writing bit0. It is not possible to set any other bits.
0x10010000
Initially this is value zero. NATIVE_FIRM writes value 1 here when a FIRM launch begins. The LGY FIRM writes value 3 here when handling PXI command 0x00020080(first TWL PXI command), it also writes value 7 here when handling PXI command 0x00030080(first AGB PXI command). This register can be read to determine what "mode" the system is running under: hard-boot, FIRM launch, or TWL/AGB FIRM.
REG_UNITINFO
This 8-bit register is value zero for retail, non-zero for dev/debug units.
REG_BOOTENV
0=Cold boot, 1=CTR, 3=TWL, 5=NTR, 7=AGB
It is unknown if this register controls anything.