This page describes the address range accessible from the ARM11, used to configure the basic GPU functionality. For information about the internal registers used for 3D rendering, see GPU/Internal Registers.
- 1 Map
- 2 Memory Fill
- 3 LCD Source Framebuffer Setup
- 4 Transfer Engine
- 5 Command List
- 6 Framebuffers
Address mappings for the external registers. GSPGPU:WriteHWRegs takes these addresses relative to 0x1EB00000.
|0x1EF00010||0x10400010||16||Memory Fill1 "PSC0"||GX command 2|
|0x1EF00020||0x10400020||16||Memory Fill2 "PSC1"||GX command 2|
|0x1EF00030||0x10400030||4||VRAM bank control||Bits 8-11 = bank[i] disabled; other bits are unused|
|0x1EF00034||0x10400034||4||GPU Busy||Bit31 = cmd-list busy, bit27 = PSC0 busy, bit26 = PSC1 busy.|
|0x1EF00050||0x10400050||4||?||Writes 0x22221200 on GPU init.|
|0x1EF00054||0x10400054||4||?||Writes 0xFF2 on GPU init.|
|0x1EF000C0||0x104000C0||4||Backlight control||Writes 0x0 to allow backlights to turn off, 0x20000000 to force them always on.|
|0x1EF00400||0x10400400||0x100||Framebuffer Setup "PDC0" (top screen)|
|0x1EF00500||0x10400500||0x100||Framebuffer Setup "PDC1" (bottom)|
|0x1EF00C00||0x10400C00||?||Transfer Engine "DMA"|
|0x1EF01000/0x10401000 - 0x1EF01C00/0x10401C00 maps to GPU internal registers. These registers are usually not read/written directly here, but are written using the command list interface below (corresponding to the GPUREG_CMDBUF_* internal registers)|
|0x1EF01000||0x10401000||0x4||?||Writes 0 on GPU init and before the Command List is used|
|0x1EF01080||0x10401080||0x4||?||Writes 0x12345678 on GPU init.|
|0x1EF010C0||0x104010C0||0x4||?||Writes 0xFFFFFFF0 on GPU init.|
|0x1EF010D0||0x104010D0||0x4||?||Writes 1 on GPU init.|
|0x1EF018E0||0x104018E0||0x14||Command List "P3D"|
|0x1EF000X0||Buffer start physaddr >> 3|
|0x1EF000X4||Buffer end physaddr >> 3|
|0x1EF000XC||Control. bit0: start/busy, bit1: finished, bit8-9: fill-width (0=16bit, 1=3=24bit, 2=32bit)|
Memory fills are used to initialize buffers in memory with a given value, similar to memset. A memory fill is triggered by setting bit0 in the control register. Doing so aborts any running memory fills on that filling unit. Upon completion, the hardware unsets bit0 and sets bit1 and fires interrupt PSC0.
These registers are used by GX SetMemoryFill.
LCD Source Framebuffer Setup
All of these registers must be accessed with 32bit operations regardless of the registers' actual bit size.
|0x00||H-total (V-total on not physically rotated screens).||12bits.
Setting this value too low will make the screen not be able to sync any pixels other than a single one from the wrong location. The lowest the screen can handle is 0x1C2, at 0x1C1 the display loses a few scanlines worth of pixel clock (though not noticable).
|0x04||HBlank timer(?)||Seems to determine the horizontal blanking interval.
Setting this to higher than
Setting this to higher than
|0x08||?||must be >= REG#0x00|
|0x0C||?||must be >= REG#0x08|
|0x10||Window X start (LgyFb)||Offsets the viewing window on the display's physical X co-ordinate relative to its front porch end.
Outside of LgyFb changing this value only seems to cause weird pixel interpolation and blurryness.
|0x14||Window X end (LgyFb)||Window X start + window width - 1 is written here to set the end display scan pixel offset.
Outside of LgyFb it seems to offset the screen to the left if this value is high enough, but can glitch out the syncing on the bottom screen. High enough values will make the screen skip too many "pixels". If this value is higher or equal to *some value* (aka. if less than one pixel per line is displayed on the screen) then the screen will lose synchronization.
|0x18||Window Y start (LgyFb)||Offsets the viewing window on the display's physical Y co-ordinate relative to the first visible scanline.|
|0x20||Low: Window Y end (LgyFb)
|Low: Window Y start + window height - 1 is written here to set the last display scanline relative to the first visible scanline.
High: This is cleared to zero when displaying LgyFb. Outside of LgyFb this doesn't really seem to do anything useful.
|0x24||V-total (H-total on not physically rotated screens).||Total scanlines including porches/sync timing. Setting this to 494 for the topscreen lowers framerate to about 50.040660858 Hz.|
|0x28||VBlank timer(?)||Seems to determine the vertical blanking interval.
Setting this to higher than
Setting this to higher than
|0x30||VTotal||Total amount of vertical scanlines in the pixel buffer, must be bigger than *an unknown blanking-like value*. If this value is less than VDisp then the last two scanlines will be repeated interlaced until VDisp is reached.|
|0x34||VDisp(?)||Total amonut of vertical scanlines displayed (only for top screen it seems like). If this value is less than VTotal then the rest of the scanlines will not be updated on the screen, so those will slowly fade out. Must be bigger than *an unknown blanking-like value*, otherwise an underflow will happen.|
|0x38||Vertical data offset(?)||??? Seems to offset the screen upwards if this value is high enough. If this value is higher or equal to *some value* (aka. if less than one scanline is displayed on the screen) then the screen will lose synchronization.|
|0x44||???||similar functionality to 0x10|
|0x48||???||bit0 seems to disable HSync, bit8 seems to disable VSync, rest of the bits aren't writable.|
|0x4C||Overscan filler color|
|0x50||Horizontal position counter||read-only|
|0x54||Horizontal scanline (HBlank) counter||read-only|
|0x5C||???||low u16: framebuffer width
high u16: framebuffer height??? (seems to be unused)
|0x60||???||low u16: timing data(?)
high u16: framebuffer total width (amount of pixels blitted regardless of framebuffer width)
|0x64||???||low u16: unknown
high u16: framebuffer total height (amount of scanlines blitted regardless of framebuffer height)
|0x68||Framebuffer A first address||For top screen, this is the left eye 3D framebuffer.|
|0x6C||Framebuffer A second address||For top screen, this is the left eye 3D framebuffer.|
|0x70||Framebuffer format||Bit0-15: framebuffer format, bit16-31: unknown|
|0x74||PDC control||Bit 0: Enable display controller.
Bit 8: H(Blank?) IRQ mask (0 = enabled). Bit 9: VBlank IRQ mask (0 = enabled). Bit 10: Error IRQ mask? (0 = enabled). Bit 16: Output enable?
|0x78||Framebuffer select and status||Bit 0: Next framebuffer to display (after VBlank).
Bit 4: Currently displaying framebuffer? Bit 8: Reset FIFO? Bit 16: H(Blank?) IRQ status/ack. Write 1 to aknowledge. Bit 17: VBlank IRQ status/ack. Bit 18: Error IRQ status/ack?
|0x80||Color lookup table index select||8bits, write-only|
|0x84||Color lookup table indexed element||Contains the value of the color lookup table indexed by the above register, 24bits, RGB8 (0x00BBGGRR)
Accessing this register will increase the index register by one
|0x90||Framebuffer stride||Distance in bytes between the start of two framebuffer rows (must be a multiple of 8).|
|0x94||Framebuffer B first address||For top screen, this is the right eye 3D framebuffer. Unused for bottom screen.|
|0x98||Framebuffer B second address||For top screen, this is the right eye 3D framebuffer. Unused for bottom screen.|
|5||Enable parallax barrier (i.e. 3D).|
|6||1 = main screen, 0 = sub screen. However if bit5 is set, this bit is cleared.|
|9-8||Value 1 = unknown: get rid of rainbow strip on top of screen, 3 = unknown: black screen.|
GSP module only allows the LCD stereoscopy to be enabled when bit5=1 and bit6=0 here. When GSP module updates this register, GSP module will automatically disable the stereoscopy if those bits are not set for enabling stereoscopy.
Framebuffer color formats
Color components are laid out in reverse byte order, with the most significant bits used first (i.e. non-24-bit pixels are stored as a little-endian values). For instance, a raw data stream of two GL_RGB565_OES pixels looks like GGGBBBBB RRRRRGGG GGGBBBBB RRRRRGGG.
|0x1EF00C00||Input physical address >> 3|
|0x1EF00C04||Output physical address >> 3|
|0x1EF00C08||DisplayTransfer output width (bits 0-15) and height (bits 16-31).|
|0x1EF00C0C||DisplayTransfer input width and height.|
|0x1EF00C10||Transfer flags. (See below)|
|0x1EF00C14||GSP module writes value 0 here prior to writing to 0x1EF00C18, for cmd3.|
|0x1EF00C18||Setting bit0 starts the transfer. Upon completion, bit0 is unset and bit8 is set.|
|0x1EF00C20||TextureCopy total amount of data to copy, in bytes.|
|0x1EF00C24||TextureCopy input line width (bits 0-15) and gap (bits 16-31), in 16 byte units.|
|0x1EF00C28||TextureCopy output line width and gap.|
These registers are used by GX command 3 and 4. For cmd4, *0x1EF00C18 |= 1 is used instead of just writing value 1. The DisplayTransfer registers are only used if bit 3 of the flags is unset and ignored otherwise. The TextureCopy registers are likewise only used if bit 3 is set, and ignored otherwise.
Flags Register - 0x1EF00C10
|0||When set, the framebuffer data is flipped vertically.|
|1||When set, the input framebuffer is treated as linear and converted to tiled in the output, converts tiled->linear when unset.|
|2||This bit is required when the output width is less than the input width for the hardware to properly crop the lines, otherwise the output will be mis-aligned.|
|3||Uses a TextureCopy mode transfer. See below for details.|
|5||Don't perform tiled-linear conversion. Incompatible with bit 1, so only tiled-tiled transfers can be done, not linear-linear.|
|10-8||Input framebuffer color format, value0 and value1 are the same as the LCD Source Framebuffer Formats (usually zero)|
|14-12||Output framebuffer color format|
|16||Use 32x32 block tiling mode, instead of the usual 8x8 one. Output dimensions must be multiples of 32, even if cropping with bit 2 set above.|
|24-25||Scale down the input image using a box filter. 0 = No downscale, 1 = 2x1 downscale. 2 = 2x2 downscale, 3 = invalid|
When bit 3 of the control register is set, the hardware performs a TextureCopy-mode transfer. In this mode, all other bits of the control register (except for bit 2, which still needs to be set correctly) and the regular dimension registers are ignored, and no format conversions are done. Instead, it performs a raw data copy from the source to the destination, but with a configurable gap between lines. The total amount of bytes to copy is specified in the size register, and the hardware loops reading lines from the input and writing them to the output until this amount is copied. The "gap" specified in the input/output dimension register is the number of chunks to skip after each "width" chunks of the input/output, and is NOT counted towards the total size of the transfer.
By correctly calculating the input and output gap sizes it is possible to use this functionality to copy arbitrary sub-rectangles between differently-sized framebuffers or textures, which is one of its main uses over a regular no-conversion DisplayTransfer. When copying tiled textures/framebuffers it's important to remember that the contents of a tile are laid out sequentially in memory, and so this should be taken into account when calculating the transfer parameters.
Specifying invalid/junk values for the TextureCopy dimensions can result in the GPU hanging while attempting to process this TextureCopy.
|0x1EF018E0||Buffer size in bytes >> 3|
|0x1EF018E8||Buffer physical address >> 3|
|0x1EF018F0||Setting bit0 to 1 enables processing GPU command execution. Upon completion, bit0 seems to be reset to 0.|
These LCD framebuffers normally contain the last rendered frames from the GPU. The framebuffers are drawn from left-to-right, instead of top-to-bottom.(Thus the beginning of the framebuffer is drawn starting at the left side of the screen)
Both of the 3D screen left/right framebuffers are displayed regardless of the 3D slider's state, however when the 3D slider is set to "off" the 3D effect is disabled. Normally when the 3D slider's state is set to "off" the left/right framebuffer addresses are set to the same physical address. When the 3D effect is disabled and the left/right framebuffers are set to separate addresses, the LCD seems to alternate between displaying the left/right framebuffer each frame.
Init Values from nngxInitialize for Top Screen
- 0x1EF00400 = 0x1C2
- 0x1EF00404 = 0xD1
- 0x1EF00408 = 0x1C1
- 0x1EF0040C = 0x1C1
- 0x1EF00410 = 0
- 0x1EF00414 = 0xCF
- 0x1EF00418 = 0xD1
- 0x1EF0041C = 0x1C501C1
- 0x1EF00420 = 0x10000
- 0x1EF00424 = 0x19D
- 0x1EF00428 = 2
- 0x1EF0042C = 0x1C2
- 0x1EF00430 = 0x1C2
- 0x1EF00434 = 0x1C2
- 0x1EF00438 = 1
- 0x1EF0043C = 2
- 0x1EF00440 = 0x1960192
- 0x1EF00444 = 0
- 0x1EF00448 = 0
- 0x1EF0045C = 0x19000F0
- 0x1EF00460 = 0x1c100d1
- 0x1EF00464 = 0x1920002
- 0x1EF00470 = 0x80340
- 0x1EF0049C = 0
More Init Values from nngxInitialize for Top Screen
- 0x1EF00468 = 0x18300000, later changed by GSP module when updating state, framebuffer
- 0x1EF0046C = 0x18300000, later changed by GSP module when updating state, framebuffer
- 0x1EF00494 = 0x18300000
- 0x1EF00498 = 0x18300000
- 0x1EF00478 = 1, doesn't stay 1, read as 0
- 0x1EF00474 = 0x10501