GPIO Registers

Registers

GPIO

Old3DS	Name	Address	Width
Yes	GPIO1_DATA	0x10147000	1
Yes	GPIO2_DATA	0x10147010	1
Yes	GPIO2_DIR	0x10147011	1
Yes	GPIO2_INTCFG	0x10147012	1
Yes	GPIO2_INTEN	0x10147013	1
Yes	GPIO2_DATA2	0x10147014	2
Yes	GPIO3_DATA	0x10147020	2
Yes	GPIO3_DIR	0x10147022	2
Yes	GPIO3_INTCFG	0x10147024	2
Yes	GPIO3_INTEN	0x10147026	2
Yes	GPIO3_DATA2	0x10147028	2

Legacy RTC

Name	Address	Width	Description
RTC_CNT	0x10147100	2	Control register
RTC_REG_STAT1	0x10147110	1	Rtc status register 1 (command 0). Bitswapped
RTC_REG_STAT2	0x10147111	1	Rtc status register 2 (command 1). Bitswapped
RTC_REG_CLKADJ	0x10147112	1	Rtc clock adjustment register (command 6). Bitswapped
RTC_REG_FREE	0x10147113	1	The free general purpose rtc register (command 7). Bitswapped
RTC_REG_TIME1	0x10147120	4	Byte-wise bit-swapped (bit7 is bit0, etc.) BCD RTC (byte0 = seconds, byte1 = minutes, byte2 = hours, byte3 = day of week)
RTC_REG_TIME2	0x10147124	4 (3?)	Day, month and year all byte-wise bit-swapped
RTC_REG_ALRMTIM1	0x10147130	4 (3?)	Rtc alarm time register 1 (command 4). Byte-wise bit-swapped
RTC_REG_ALRMTIM2	0x10147134	4 (3?)	Rtc alarm time register 2 (command 5). Byte-wise bit-swapped
RTC_REG_COUNT	0x10147140	4 (3?)	Rtc dsi counter register (ex command 0). Byte-wise bit-swapped
RTC_REG_FOUT1	0x10147150	1	Rtc dsi fout register 1 (ex command 1). Bitswapped
RTC_REG_FOUT2	0x10147151	1	Rtc dsi fout register 2 (ex command 2). Bitswapped
RTC_REG_ALRMDAT1	0x10147160	4 (3?)	Rtc dsi alarm date register 1 (ex command 4). Byte-wise bit-swapped
RTC_REG_ALRMDAT2	0x10147164	4 (3?)	Rtc dsi alarm date register 2 (ex command 5). Byte-wise bit-swapped

Descriptions

GPIO

GPIO pins

Only GPIO2 and GPIO3 pins have their interrupts configurable. Active low pins should be configured as "falling edge", and output ports shouldn't have interrupts enabled at all.

GPIO Services bitmasks use this table, in that order:

Bit	IRQ ID	Description
0	?	Debug button (?) (active-low)
1	0x63 (falling edge)	Touch Screen (active low, 0 = screen pressed)
2	0x60 (falling edge) 0x62 (rising edge)	Shell closed
0	0x64	Headphones inserted
1	0x66	TWL depop circuit (?) (active-low)
DATA2.0	-	GPIO2_DATA2_0 (wifi related?)
0	0x68	C-stick interrupt
1	0x69	IrDA interrupt (active-low)
2	0x6A	Gyro interrupt
3	0x6B	C-stick "stop" (output)
4	0x6C	IrDA TX-RC (output)
5	0x6D	IrDA RXD (active-low)
6	0x6E	NFC output1 (?)
7	0x6F	NFC output2 (?)
8	0x70	Headphones button/half-inserted (active-low)
9	0x71	MCU interrupt
10	0x72	NFC interrupt (?)
11	0x73	QTM output (?)
DATA2.0	-	GPIO3_DATA2_0 (wifi related?)

GPIOn_DATA

Pin values, one bit per pin.

GPIOn_DIR

Pin directions for GPIO2 and GPIO3, one bit per pin.

Value	Description
0	Input
1	Output

GPIOn_INTCFG

Interrupt configuration for GPIO2 and GPIO3 pins (not the extra ones), one bit per pin.

Value	Description
0	Falling edge
1	Rising edge

GPIOn_INTEN

Interrupt enable bits for GPIO2 and GPIO3 pins (not the extra ones), one bit per pin.

Value	Description
0	Interrupt disabled
1	Interrupt enabled

GPIOn_DATA2

Extra pins for GPIO2 and GPIO3 (one bit each). These two pins, in total, are not bound to any IRQ and are not configurable.

Default values

After bootrom initialization, these are the values of the registers:

Address	Value
0x10147000	0x0003
0x10147010	0x00000002
0x10147014	0x0000
0x10147020	0x00000DFB
0x10147024	0x00000000
0x10147028	0x0000

Legacy RTC

RTC_CNT (0x10147100)

Bit	Description
0	Latch STAT1
1	Latch STAT2
2	Latch CLKADJ
3	Latch FREE
4	Latch TIME
5	Latch ALRMTIM1
6	Latch ALRMTIM2
7	Latch COUNT
8	Latch FOUT1
9	Latch FOUT2
10	Latch ALRMDAT1
11	Latch ALRMDAT2
12	ARM7 Busy? This may be chipselect
13	ARM7 write command received? (writing 1 clears it seems)
14	ARM7 read command recieved? (writing 1 clears it seems)
15	DS SIO SI pin (rtc irq pin)