Difference between revisions of "SPICARD Registers"
Jump to navigation
Jump to search
m (→NSPI_FIFO) |
|||
| (8 intermediate revisions by 3 users not shown) | |||
| Line 5: | Line 5: | ||
! Address | ! Address | ||
! Width | ! Width | ||
| + | ! RW | ||
! Used by | ! Used by | ||
|- | |- | ||
| style="background: green" | Yes | | style="background: green" | Yes | ||
| − | | | + | | [[#NSPI_CNT|NSPI_CNT]] |
| 0x1000D800 | | 0x1000D800 | ||
| 4 | | 4 | ||
| + | | RW | ||
| | | | ||
|- | |- | ||
| style="background: green" | Yes | | style="background: green" | Yes | ||
| − | | | + | | [[#NSPI_DONE|NSPI_DONE]] |
| 0x1000D804 | | 0x1000D804 | ||
| 4 | | 4 | ||
| + | | RW | ||
| | | | ||
|- | |- | ||
| style="background: green" | Yes | | style="background: green" | Yes | ||
| − | | | + | | [[#NSPI_BLKLEN|NSPI_BLKLEN]] |
| 0x1000D808 | | 0x1000D808 | ||
| 4 | | 4 | ||
| + | | RW | ||
| | | | ||
|- | |- | ||
| style="background: green" | Yes | | style="background: green" | Yes | ||
| − | | | + | | [[#NSPI_FIFO|NSPI_FIFO]] |
| 0x1000D80C | | 0x1000D80C | ||
| 4 | | 4 | ||
| + | | RW | ||
| | | | ||
|- | |- | ||
| style="background: green" | Yes | | style="background: green" | Yes | ||
| − | | | + | | [[#NSPI_STATUS|NSPI_STATUS]] |
| 0x1000D810 | | 0x1000D810 | ||
| 4 | | 4 | ||
| + | | R | ||
| | | | ||
|- | |- | ||
| style="background: green" | Yes | | style="background: green" | Yes | ||
| − | | | + | | [[#NSPI_AUTOPOLL|NSPI_AUTOPOLL]] |
| 0x1000D814 | | 0x1000D814 | ||
| 4 | | 4 | ||
| + | | RW | ||
| | | | ||
|- | |- | ||
| style="background: green" | Yes | | style="background: green" | Yes | ||
| − | | | + | | [[#NSPI_INT_MASK|NSPI_INT_MASK]] |
| 0x1000D818 | | 0x1000D818 | ||
| 4 | | 4 | ||
| + | | W? | ||
| | | | ||
|- | |- | ||
| style="background: green" | Yes | | style="background: green" | Yes | ||
| − | | | + | | [[#NSPI_INT_STAT|NSPI_INT_STAT]] |
| 0x1000D81C | | 0x1000D81C | ||
| 4 | | 4 | ||
| + | | RW | ||
| | | | ||
|} | |} | ||
| + | |||
| + | == NSPI_CNT == | ||
| + | {| class="wikitable" border="1" | ||
| + | ! BIT | ||
| + | ! DESCRIPTION | ||
| + | |- | ||
| + | | 0-2 | ||
| + | | [[Filesystem_services#CardSpiBaudRate|Baud Rate]] | ||
| + | |- | ||
| + | | 6-7 | ||
| + | | Unused device select. | ||
| + | |- | ||
| + | | 12 | ||
| + | | [[Filesystem_services#CardSpiBusMode|Bus Mode]] | ||
| + | |- | ||
| + | | 13 | ||
| + | | Transfer Mode (0 = read, 1 = write) | ||
| + | |- | ||
| + | | 15 | ||
| + | | Trigger (0 = idle, 1 = busy) | ||
| + | |} | ||
| + | |||
| + | This register seems to have a bug where the lower 8 bits are shifted up by 16 when reading this register. | ||
| + | |||
| + | == NSPI_DONE == | ||
| + | Contains 1 when the SPI slave is selected. A 0 is written here on transfer end to deselect the slave. | ||
| + | |||
| + | == NSPI_BLKLEN == | ||
| + | {| class="wikitable" border="1" | ||
| + | ! BIT | ||
| + | ! DESCRIPTION | ||
| + | |- | ||
| + | | 0-20 | ||
| + | | Transfer size | ||
| + | |- | ||
| + | | 21-31 | ||
| + | | Unused | ||
| + | |} | ||
| + | |||
| + | == NSPI_FIFO == | ||
| + | {| class="wikitable" border="1" | ||
| + | ! BIT | ||
| + | ! DESCRIPTION | ||
| + | |- | ||
| + | | 0-31 | ||
| + | | Data | ||
| + | |} | ||
| + | |||
| + | This FIFO is one way (half-duplex). | ||
| + | |||
| + | == NSPI_STATUS == | ||
| + | {| class="wikitable" border="1" | ||
| + | ! BIT | ||
| + | ! DESCRIPTION | ||
| + | |- | ||
| + | | 0 | ||
| + | | FIFO Full (0 = not full, 1 = full) | ||
| + | |} | ||
| + | |||
| + | == NSPI_AUTOPOLL == | ||
| + | {| class="wikitable" border="1" | ||
| + | ! BIT | ||
| + | ! DESCRIPTION | ||
| + | |- | ||
| + | | 0-7 | ||
| + | | Command | ||
| + | |- | ||
| + | | 16-19 | ||
| + | | Timeout (Tries = 31<<Baudrate (from NSPI_CNT) + Timeout) | ||
| + | |- | ||
| + | | 24-26 | ||
| + | | Bit offset (0-7) | ||
| + | |- | ||
| + | | 30 | ||
| + | | Poll for a set or unset bit | ||
| + | |- | ||
| + | | 31 | ||
| + | | 1 = Enable/Busy | ||
| + | |} | ||
| + | |||
| + | This automatically sends a command to the device and compares the specified bit in the response with bit 30 until it matches or a timeout occurs. Nintendo uses a timeout of 10 which roughly equals 1 second. This is used in Process9 to poll the gamecard SPI flash status register for write operation finished or write enable. | ||
| + | |||
| + | == NSPI_INT_MASK == | ||
| + | {| class="wikitable" border="1" | ||
| + | ! BIT | ||
| + | ! DESCRIPTION | ||
| + | |- | ||
| + | | 0 | ||
| + | | Transfer finished (1 = disabled) | ||
| + | |- | ||
| + | | 1 | ||
| + | | Autopoll success (1 = disabled) | ||
| + | |- | ||
| + | | 2 | ||
| + | | Autopoll timeout (1 = disabled) | ||
| + | |} | ||
| + | |||
| + | == NSPI_INT_STAT == | ||
| + | {| class="wikitable" border="1" | ||
| + | ! BIT | ||
| + | ! DESCRIPTION | ||
| + | |- | ||
| + | | 0 | ||
| + | | Transfer finished (also fires on each autopoll try?) | ||
| + | |- | ||
| + | | 1 | ||
| + | | Autopoll success | ||
| + | |- | ||
| + | | 2 | ||
| + | | Autopoll timeout | ||
| + | |} | ||
| + | |||
| + | [[IRQ_Registers|Interrupt]] ID 23 is fired when any of the bits change to 1 except for interrupts masked in [[#NSPI_INT_MASK|NSPI_INT_MASK]]. Writing 1 to a bit in this register aknowledges the interrupt. | ||
Latest revision as of 00:08, 15 February 2021
Registers[edit]
| Old3DS | Name | Address | Width | RW | Used by |
|---|---|---|---|---|---|
| Yes | NSPI_CNT | 0x1000D800 | 4 | RW | |
| Yes | NSPI_DONE | 0x1000D804 | 4 | RW | |
| Yes | NSPI_BLKLEN | 0x1000D808 | 4 | RW | |
| Yes | NSPI_FIFO | 0x1000D80C | 4 | RW | |
| Yes | NSPI_STATUS | 0x1000D810 | 4 | R | |
| Yes | NSPI_AUTOPOLL | 0x1000D814 | 4 | RW | |
| Yes | NSPI_INT_MASK | 0x1000D818 | 4 | W? | |
| Yes | NSPI_INT_STAT | 0x1000D81C | 4 | RW |
NSPI_CNT[edit]
| BIT | DESCRIPTION |
|---|---|
| 0-2 | Baud Rate |
| 6-7 | Unused device select. |
| 12 | Bus Mode |
| 13 | Transfer Mode (0 = read, 1 = write) |
| 15 | Trigger (0 = idle, 1 = busy) |
This register seems to have a bug where the lower 8 bits are shifted up by 16 when reading this register.
NSPI_DONE[edit]
Contains 1 when the SPI slave is selected. A 0 is written here on transfer end to deselect the slave.
NSPI_BLKLEN[edit]
| BIT | DESCRIPTION |
|---|---|
| 0-20 | Transfer size |
| 21-31 | Unused |
NSPI_FIFO[edit]
| BIT | DESCRIPTION |
|---|---|
| 0-31 | Data |
This FIFO is one way (half-duplex).
NSPI_STATUS[edit]
| BIT | DESCRIPTION |
|---|---|
| 0 | FIFO Full (0 = not full, 1 = full) |
NSPI_AUTOPOLL[edit]
| BIT | DESCRIPTION |
|---|---|
| 0-7 | Command |
| 16-19 | Timeout (Tries = 31<<Baudrate (from NSPI_CNT) + Timeout) |
| 24-26 | Bit offset (0-7) |
| 30 | Poll for a set or unset bit |
| 31 | 1 = Enable/Busy |
This automatically sends a command to the device and compares the specified bit in the response with bit 30 until it matches or a timeout occurs. Nintendo uses a timeout of 10 which roughly equals 1 second. This is used in Process9 to poll the gamecard SPI flash status register for write operation finished or write enable.
NSPI_INT_MASK[edit]
| BIT | DESCRIPTION |
|---|---|
| 0 | Transfer finished (1 = disabled) |
| 1 | Autopoll success (1 = disabled) |
| 2 | Autopoll timeout (1 = disabled) |
NSPI_INT_STAT[edit]
| BIT | DESCRIPTION |
|---|---|
| 0 | Transfer finished (also fires on each autopoll try?) |
| 1 | Autopoll success |
| 2 | Autopoll timeout |
Interrupt ID 23 is fired when any of the bits change to 1 except for interrupts masked in NSPI_INT_MASK. Writing 1 to a bit in this register aknowledges the interrupt.