Difference between revisions of "DSP Memory Region"
m (clarify buffer ids) |
|||
| Line 232: | Line 232: | ||
| 1 | | 1 | ||
| u8 | | u8 | ||
| − | | Dirty flag for | + | | Dirty flag for buffer id, set to 1 when buffer (after the first) starts playing |
|- | |- | ||
| 2 | | 2 | ||
| Line 244: | Line 244: | ||
| 8 | | 8 | ||
| u16 | | u16 | ||
| − | | Buffer id of | + | | Buffer id of the buffer that's just started playing. |
|- | |- | ||
| 10 | | 10 | ||
Revision as of 15:29, 24 March 2016
Some of this is known to be incorrect. I'll correct this in a few months after a bit more RE work. Merry (talk) 21:10, 28 January 2016 (CET)
- Note that everything below will vary depending on the exact DSP firmware used and different variants have slightly different behaviours.*
The DSP communicates with the application through two shared memory areas 0x8000 bytes long each (at 0x1FF50000 and 0x1FF70000 respectively). The DSP alternates between the use of these two areas (much like a double-buffer). Each area has 15 structures within it. The location of these structures can be obtained by reading channel 2 of the DSP pipe. A list of structures in the order the DSP addresses are read from the pipe follows:
1. Frame count
2. Input configurations
3. Input status
4. Input ADPCM coefficients
5. DSP configuration
6. DSP status
7. Output samples
8. Intermediate mix samples
9. Compressor table
10. DSP debug statistics
11. Unknown Coefficients
12. Unknown Coefficients
13. Unknown Coefficients
14. Surround sound biquad filter 1
15. Surround sound biquad filter 2
The DSP has 24 inputs, each of which are individually configurable. These 24 inputs each produce three sets of 4 audio channels (two left, two right).
These four audio channels feed into three intermediate mixers. Two of these intermediate mixers are used for effects and aux.
Frame Count
Input Config
A 192 byte long structure. There are 24 of them.
| Offset | Type | Description |
| 0 | u32 | Dirty flags |
| 4 | f32[3][2][2] | Input Gain (Each input has 12 channels) |
| 52 | f32 | Rate multiplier (1.0x == native DSP rate) |
| 56 | u8 | Interpolation mode |
| 57 | u8 | Polyphase filter select |
| 58 | u16 | bit[0]: Simple Filter enabled, bit[1]: Biquadratic Filter enabled |
| 60 | SimpleFilter | Simple Filter (One pole normalized recursive linear filter) |
| 64 | BiquadFilter | Biquadratic Filter (Two poles two zeros normalized recursive linear filter) |
| 74 | u16 | Bitmap of which buffers in queue are dirty |
| 76 | Buffer[4] | Buffer queue |
| 156 | u32 | - |
| 160 | u16 | Is Active |
| 162 | u16 | Sync Count |
| 164 | u32 | Play position |
| 168 | 4 | ? |
| 172 | u32 | Physical address of embedded buffer |
| 176 | u32 | Number of samples in embedded buffer |
| 180 | u16 | bits[0:1]: 1 = mono, 2 = stereo; bits[2:3]: buffer format, bits[5]: fade in |
| 182 | AdpcmData | ADPCM data associated with embedded buffer |
| 188 | u16 | bit[0]: ADPCM updated?; bit[1]: Is looping?r |
| 190 | u16 | Buffer Id of embedded buffer |
Buffer
| Offset | Type | Description |
| 0 | u32 | Physical Address |
| 4 | u32 | Sample Count |
| 8 | AdpcmData | ADPCM data |
| 14 | u8 | ADPCM data dirty? |
| 15 | u8 | Looping? |
| 16 | u16 | Buffer Id |
| 18 | u16 | - |
Adpcm Data
| 0 | u8 | ADPCM predictor/scale |
| 1 | u8 | - |
| 2 | s16 | ADPCM y[n-1] |
| 4 | s16 | ADPCM y[n-2] |
Simple Filter
This is a standard single-pole filter. The fall-off is 6dB per octave as you would expect.
| Offset | Type | Description |
| 0 | s1.15 | b0 |
| 2 | s1.15 | a1 |
Input status
Read only. This structure is set by the DSP. This structure is 12 bytes long and there are 24 of them.
| Offset | Type | Description |
| 0 | u8 | Input Enabled? |
| 1 | u8 | Dirty flag for buffer id, set to 1 when buffer (after the first) starts playing |
| 2 | u16 | Sync count |
| 4 | u32 | Position (number of samples) into current buffer playback |
| 8 | u16 | Buffer id of the buffer that's just started playing. |
| 10 | u16 | - |
Input ADPCM coefficients
This is a 32 byte long structure. There are 24 of them.
| Offset | Type | Description |
| 0 | s5.11[16] | ADPCM coefficents |
DSP configuration
Delay Effect
Delay with feedback.
Length of delay is expressed in terms of number of audio frames (there are 160 samples per audio frame).
Feedback arm only has a gain on it. Under the feedback arm is a single-pole filter with the delay.
Reverb Effect
Reverb consists of two comb filters and one all-pass filter in standard configuration.
DSP status
Read only.
Output samples
Read only. This structure is 320 bytes long.
| Offset | Type | Description |
| 0 | s16[160] | Samples |
Intermediate mix samples
Read/Write.
PCM32. Also serves an aux function, allowing the ARM11 to apply custom effects to audio.
This structure is 5120 bytes long.
| Offset | Type | Description |
| 0 | s32[2][4][160] | Samples |
Compressor table
A precomputed response curve lookup table for the compressor.