IRU:SetIRLEDState - Revision history

Yellows8: /* Description */

2015-03-29T23:24:41Z

Description

← Older revision		Revision as of 03:24, 30 March 2015
Line 26:		Line 26:

	=Description=		=Description=
	Value 1 enables the IR LED, while value 0 disables it. Note that the IR LED will automatically turn off after a certain amount of time if left on this way, however to turn it back on the state has to be set to value zero first. This is set via GPIO : it writes 0x10 to 0x10147020 (0x1EC47020 in process space) to enable the LED, and clears that bit to disable it.		Value 1 enables the IR LED, while value 0 disables it. Note that the IR LED will automatically turn off after a certain amount of time if left on this way, however to turn it back on the state has to be set to value zero first. This is set via a GPIO service command, the GPIO module then does the following: it writes 0x10 to 0x10147020 (0x1EC47020 in process space) to enable the LED, and clears that bit to disable it.

Smea at 01:18, 30 March 2015

2015-03-29T23:18:06Z

← Older revision		Revision as of 03:18, 30 March 2015
Line 26:		Line 26:

	=Description=		=Description=
	Value 1 enables the IR LED, while value 0 disables it. Note that the IR LED will automatically turn off after a certain amount of time if left on this way, however to turn it back on the state has to be set to value zero first. This is set via GPIO.		Value 1 enables the IR LED, while value 0 disables it. Note that the IR LED will automatically turn off after a certain amount of time if left on this way, however to turn it back on the state has to be set to value zero first. This is set via GPIO : it writes 0x10 to 0x10147020 (0x1EC47020 in process space) to enable the LED, and clears that bit to disable it.

Yellows8: /* Description */

2014-02-22T03:53:42Z

Description

← Older revision		Revision as of 06:53, 22 February 2014
Line 26:		Line 26:

	=Description=		=Description=
	Value 1 enables the IR LED, while value 0 disables it. Note that the IR LED will automatically turn off after a certain amount of time if left on this way, however to turn it back on the state has to be set to value zero first.		Value 1 enables the IR LED, while value 0 disables it. Note that the IR LED will automatically turn off after a certain amount of time if left on this way, however to turn it back on the state has to be set to value zero first. This is set via GPIO.

Yellows8: Created page with "=Request= {| class="wikitable" border="1" |- ! Index Word ! Description |- | 0 | Header code [0x000B0040] |- | 1 | u32 value |} =Response= {| class="wikitable" border="1" |- !..."

2014-02-22T01:49:29Z

Created page with "=Request= {| class="wikitable" border="1" |- ! Index Word ! Description |- | 0 | Header code [0x000B0040] |- | 1 | u32 value |} =Response= {| class="wikitable" border="1" |- !..."

New page

=Request=
{| class="wikitable" border="1"
|-
! Index Word
! Description
|-
| 0
| Header code [0x000B0040]
|-
| 1
| u32 value
|}

=Response=
{| class="wikitable" border="1"
|-
! Index Word
! Description
|-
| 0
| Header code
|-
| 1
| Result code
|}

=Description=
Value 1 enables the IR LED, while value 0 disables it. Note that the IR LED will automatically turn off after a certain amount of time if left on this way, however to turn it back on the state has to be set to value zero first.